Lian Li O11D EVO RGB E-ATX gaming dual chamber case - ARGB lighting strips - Up to 420mm radiator - Cable management - Front and side tempered glass panels - Reversible chassis (O11DERGBX.US)

This case is, by far, one of the best cases I've ever had the pleasure of building a system with. Its dual chamber design makes an easy job of cable management and creating a supremely clean build. It has ample airflow options, ample mounting options for virtually everything and it is STUNNING to see in person filled with RGB fans and gizmos!One thing that surprised me is the fan noise. It's basically silent. Just to test, I set every fan and the pump to 100% and it's... silent. It does a great job at silencing the fans. I currently have all 120mm fans, but I will be swapping out the bottom intake fans to the 140mm size at some point for the additional airflow they can provide at slower RPMs, but even if you use all 120mm fans like I did, you just won't hear them. The built-in RGB light strips on the top and bottom of the O11D-Evo look exceptional if you're going for that Flashy, Ritzy build, too!My only question is... Why couldn't we have had this case 25 years ago?THIS is the future of PC cases. Whether you're someone that wants to build a clean, modern, blacked out look with no lights or you're someone that wants all the flash you can possibly cram into a PC case... This is what you're looking for.Do be aware, however, that there are *ZERO* external bays. You won't be putting an internal CD/DVD/Blu-Ray drive or anything else that requires an external 3.5" or 5.25" bay. This case just doesn't have it... But let's all be honest here, who uses those these days? I've been building PCs since the late 1980's and in the past 10 years, I haven't had the need of an external drive bay for ANYTHING.Get this case. Or ANY of the Lian Li O11 cases. You won't be dissatisfied. You will, however, be absolutely amazed by the time you build your system! The options for mounting fans and radiators for water cooling is ample and the wide open view of your internals, especially loaded with RGB "things" is just jaw dropping! These are beautiful cases and an absolute JOY to build with!

This is hands down the best case I have ever used for a water cooling build.It has lots of space to add components and has a versatile layout that can be swapped around to accommodate any build you are trying to achieve. Support for 3 420mm rads is great. Depending on the location you choose to set your motherboard in you can add one or two additional fans in the rear of the case. There is plenty of room for both horizontal and vertical GPU mounting. There are plenty of usb ports on the front I/o panel. I am very pleased with this case for my build. It is running nice and cool and looks amazing.

If you have made it this far stop your search . Put it in your cart and you won’t be disappointedAmazing caseAmazing qualityAmazing aestheticsAmazing flexibilityAmazing airflowWould 10000% reccomend this great case .

The Item matches the description, Great quality, the Item was in Good condition & with great value. Overall, the Business was Excellent. There are no worries here. I recommend the Seller.

Muy alegre por mi case,llegó en perfectas condiciones y bien seguro

escribo esta reseña luego de 1 años, es expectacular, muy espacioso y se ve muy bonito

LARGE CASE; But great in terms of adaptability. Using a Corsair PS I had to remove the top SATA bay to allow access to the connectors; not a big deal as I am only using NVMe drives. The GPU Anti-Sag Bracket will cause the GPU to not lock into place on MSI MPG X870E Edge TI mobo. Other than that the case is modular, even though it seems to be one large structure, it is adaptable to individual needs! I am running a Ryzen 9 9950X CPU, Yeston Radeon 7800 XT Sakura GPU, 64GB Corsair Vengeance RGB RAM, Samsung 990 PRO M.2 and WD Black M.2, Corsair 120mm Fans and Corsair Titan LCD AIO for the cooler.

Background:I have 3 sets of 140mm fans. The top radiator set come with the LF 3 ARGB AIO for cpu, and are 27MM thick. The others are your standard 25MM thick fans. I have a 420MM LF3 RGB aio. The following is following these specifications.1) There are not screw holes at the top/bottom of the side panel (which was completely avoidable with a better design), which essentially forces you into either attaching a radiator, or you guessed it, a "UNI" fan where the set of fans connect as one whole. Was this a design choice to push you towards installing LL interlocking fans - I had to wonder.1.1) Because you are semi-forced to using a chonky uni-fan, you essentially need to install the side fans/radiator before the top or bottom fans. This is because there isn't enough space to get them in afterwards, especially with a 420MM radiator up top.1.2) You *can not* take the side mounting bracket out, mount your 3x 140mm fans, and put it back in. At least I couldn't. It seemed like there wasn't enough clearance. So this eliminated the ability to use all but one panel position, where the fans are pushed forward through half the rubber grommet-line. This wasn't a big deal considering that probably gives better air flow anyways - having an air pocket behind the fans, but considering the case is marketed on being so modifiable, it really only had the one option.2) If installing a 420MM radiator on top in a push configuration (at least), you are *forced* to use these included hanging brackets. That's because there's not enough room for the radiator to be flush with the top panel - and for whatever reason, the top panel even elevates above from where it is mounted by two screws to the case. So you are essentially forced into using the bottom motherboard configuration (more on this later for the bottom fan install) because even without using a push-pull configuration, with these brackets you're getting push-pull space eaten up.2.1) I'm unsure if you could attach a push-pull 3x140mm fan directly to the top panel. Since my extra fans are 27mm thick, I didn't have the right size radiator screws. (I have since ordered some but I'm returning the case). Even if it does work, you'd have to hold the radiator up to the top panel and hope the fans don't come out of alignment while hap-hazardly screwing in radiator screws through the top panel, through the fans, to the radiator. Seems like some innovation here might have been nice to be able to mount to the panel and just drop it in.2.2) The bigger issue I had was that even though I used the lower MB configuration, getting a 420mm radiator into the top panel was smashing my CPU power cables. I had to use an uncomfortable amount of force, causing a sharp ben in those cables. This may have been made even worse because I mounted the LL Edge PSU to the top position in the back chamber, which eats up the bottom half of the top cable gromets. So, the CPU cables were squeezed into the case, up, and then over the PSU in a double-L shaped bend.2.3) There is barely *any* space to get up and behind the 420mm radiator and gain access to the grommets in terms of getting cables through (like your RGB 3 pin from your AIO, or your pwm/3pin from your exhaust fan). So really, you have to install your exhaust fan and your AIO. I would have liked to be able to send the cables through there, but had to opt for the side gromets unless I pulled out the AIO radiator, and fed them through first.3) The bottom 3x140mm fans... They/youtube videos show you examples of 3x120's getting mounted to it and the panel easily sliding back into place. That's not the experience I had with 3x140's. Especially with my MB already mounted. Mind you, I didn't even use thick fans on my bottom intake, just the standard 25mm.3.1) Installing the 25mm thin fan standard to the bottom panel covers up most of the available gromet in the bottom MB configuration. The panel with the fans mounted on it would not slide into position. My MB has a 6pin gray power socket on the bottom that the fans were running into, even after I pulled out the cables coming from the bottom gromet, which were also pushing against the 140mm fans uncomfortably. I had to slightly bend the motherboard up, and use a slightly uncomfortable amount of force to get the back corner (that sits under the hd audio socket) such that the panel foot wouldn't slide into the free space underneath. This took me an hour to problem solve. I can't believe how little room there was to get the slimmest thickness of fan in there, and how little space that left for cables to get through the gromets, even if the MB was pre-installed in the lower position. It may have been impossible to install thicker fans(which I DID want to test to see if there was any impact on performance) but gave up on after that experience.4) The back panel. Top mounting my same brand LL Edge PSU at the bottom came into contact with the default cable management/ (LL hub holder?) in the back of the case. So, I installed it where the HDD/SD drives were in the top configuration. This covers up half the gromets in the top of the case on one side, making it difficult to get the PSU and other cables through, especially if you have top fans or heaven forbid, my radiator configuration up top.4.1) I really don't love the cable management brackets in this case. I've only done one other build but just having small spaces on it where you can feed flexible cable holders is the way it was done better.4.2) I didn't need the back of the MB cut out using an AMD cpu. I don't know anything about intel cpus or why this is done, but I'm guessing it's for them. I have a magnetic PWM/RGB hub that I wanted to mount, and this basically pushed me into moving my PSU up top so I could use the space below for the hub to latch on to, limiting my options.5) I like that the buttons are towards the top of the tower, but I'm confused why the input is along the bottom. Is the expectation that you have the case up on a desk? I don't have space for that, so gaining access to the front panel input is me trying to not slide face-first off my rolling feet chair to reach down and plug things in. This is not a great option for a case-on-the-floor or on a roller on the floor configuration. But if you pay a bunch of extra money and do a bunch of extra effort, maybe you can move the IO to the top side of the case? And again I feel like this is a money grab. It should just be up there by default IMO. If you have the buttons up top, you might as well have the input up there, as well because you're admitting that *that* is where things are accessible by having the buttons there. Instead of trying to make people buy an augment for the case, why not just make the default configuration better / standard, and make the augment option for this weird use-case, and be respectful to your consumers?It's disappointing in that it over-sells itself in terms of flexibility and ease of installation and modularity. If you want to use 140mm fans and a 420mm radiator, your options are pretty much just 1 option and there's only 1 good order to install the various elements in the case. I don't think it would have been nearly as difficult if I were installing pure 120's and a 360mm radiator, and a more-standard PSU. But their PSU is same-company so you'd think they'd create things that are friendly with their existing products - idk.Despite this, over all it's a really good case and it gets the job done with slightly above average airflow performance. Not the best or worse. It looks nice and at least the power button is somewhere I can easily access it, and it *can* fit 3 sets of 140MM fans. But there have to be better cases to do what I wanted to do with it. I probably should have just gone with the one I was looking at instead of this for my use-case, but was convinced by a friend I didn't need that much space - well guess what - I kinda did.This was my second build and despite knowing what I was doing, generally, it took at least 50% more time trying to figure out things that shouldn't have been that difficult.What's the value of being able to pull panels in and out if it doesn't even make the process easier. What's the value of being able to move the "front" input around the bottom of the case if the case sits on the floor?Why in the instructions isn't there a differentiation between the top panel 420mm mounting brackets that tell you one needs to go on one side so that you can "slide" it into the top of the case? Final note with the instructions.It seems you saved paper putting key, short notes in every common language on every page next to a picture, usually. But it's really confusing to navigate things that way, looking for tiny legible text next to already-small pictures. It would have been better for the consumer if you had the same information in 3 different quick install instructions. I ended up having to google things to see larger images and information about what the included screws even were, clearly.