C1U-H60 RY28140 Carburetor for Homelite CS26 Ryobi SS26 RY28120 RY28121 RY28141 RY28160 RY28161 UT33600 UT33650 308054013 308054012 308054004 308054008 String Trimmer

When the fuel lines deteriorated and fell apart,my RY28140 26cc with a Wabro WT1059 carb string trimmer would start but stall in just seconds. Priming the carb again would enable a restart,but with the same stall in just a few seconds. It was obvious it was starving for fuel. While checking for a carb kit,I saw a replacement carb was the way to go,knowing that the passages were so minute . Finding the right replacement carb for an older(2013) trimmer might be difficult. With Amazon's return policy,taking a chance on this carb was no big deal. That said,I ordered this carb,btw was very complete with fuel lines,new fuel weight filter and even a spark plug,along with a adjustment tool.It also included primer bulb rebuilt parts,making this a very good value,worth every penny. It only took acouple of minutes to remove and replace the carburetor with the new one. A few pushes on the primer bulb filled the lines and in just a couple pulls,the trimmer fired right up. It was running a bit rough and sounded a bit too rich. Using the supplied tool,turning the outside screw had no effect. Returning that screw to it's original position,I tried the inside screw. In a half turn in on that one produced a noticeable improvement in the idle and instant throttle response. All this took less than 20 minutes and I have a like-new running trimmer that will start right away and idle like it should. The 'automatic' choke release is a nice touch,also. Forget about 'rebuilding' these carbs,this replacement carb is the way to go!

Works great

This carburetor came with extra gaskets, primer bulbs, hose and more. It is an extremely easy installation with 2 simple long bolts. Only took about 10 minutes - and it only took that long because I replaced all the hoses as well, you could do it in half the time if you didn't need to - but this particular trimmer is a decade old. It is the second of it's type I have had. I have the edger, tiller, trimmer, and brush cutter attachments. With so much invested in the alternate tools it made sense to bring this back to life even though I've long since replaced it's main duty with a different weed trimmer. It hasn't ran in about 3 years at this point, and was dry as a bone as well. A little fuel, a quick check of the spark plug, primed it and a few pulls later it's running! After warming up it actually runs better than I remember. It seems to rev up faster and so the tiller does as well, which is It's main use for me - helping weed between rows in the garden. Unlike -some- of the other reviewers I have not as of yet needed to make any adjustments to the screws. I will update this review if my experience with the product changes. My main take away from this was such: Having never done much myself dealing with carburetor's this small (dealing with bigger things, 4-wheelers to cars) I never even considered that these things would be so cheap. I set this thing aside eventually planning to take it apart and give it a proper cleaning, which for $15 it's worth buying a new one instead - just to save your time. YOLO! :) I felt silly it was so easy, hopefully you do too!

Easy to use as soon as i got it hooked up my weed eater started on the second pull. I originally thought i was going to have to throw away. Best money spent

this carb worked out just fine, I put it on and made minor adjustment and my Ryobi ss30 ran great

I should have known, when buying something from China this would be a bad thing, and it was. The carburetor worked fine, and the machine started almost immediately, but here's the problem. They send new gas lines, which are absolutely a piece of trash. The lines were falling apart.... seriously. I had to drive 20 minutes each way and buy new lines. The cost for gas, time, and extra money, it is now working fine. Do not buy from this company. Pure crap

Worked out of the box. Everything required was included. There were no instructions, but to be honest if someone can't figure how to remove 2 nuts, to tubes, and 1 cable they probably should take it to a shop. Not being snarky, some people just aren'techanically inclined. It was already adjusted perfectly and needed nothing other than to be installed. My weed eater hasn't run this good since I bought it 11 years ago.

Perfect fit for my Homelite weed trimmer, carburetor exact match, plus plug, air filter, fuel filter, gas lines, gaskets and extra pump button. 15 min later running good as new.